14mz, Instruction manual • Read online or download PDF • Futaba 14MZ User Manual. Get Futaba 14MZ Manual. Get all Futaba manuals! 14MZ. 14 CHANNEL RADIO CONTROL SYSTEM. PCMG3/PCM/FM selectable. INSTRUCTION. Compact Flash (CF) Card Handling Instructions Follow these precautions when handling the CF card included in your 14MZ transmitter. DO NOT allow the.

Author: Kazrakazahn Mikajas
Country: Barbados
Language: English (Spanish)
Genre: Business
Published (Last): 28 October 2017
Pages: 157
PDF File Size: 13.81 Mb
ePub File Size: 13.36 Mb
ISBN: 670-9-48165-300-8
Downloads: 55271
Price: Free* [*Free Regsitration Required]
Uploader: Tulabar

Then you will see frequencies on the screen. Fuel Mixture Fuel Mixture Dedicated mixing used in manial adjustment of engines manal use a fuel mixture control carburetor.

V-tail is when 2 servos are used together to control rudder movement as Elevators. It is like hearing the same sentences about heading hold gyro many years ago This can be used when playing back the CF card from the PC can be played back when name of maneuvers, etc.

FUTABA 14MZ Instruction Manual

Equipment for reading and writing CF cards are available at most electronics stores. Always inspect a battery which has previously overheated for potential damage, and do not re-use if you suspect it has been damaged in any way. Water or moisture may enter the transmitter through the antenna or stick openings and cause erratic operation or loss of control. Clock This shows the today’s date and the current time. Motor [Corresponding model type]: Analytical cookies which allow anonymous analysis of the behavior of web users and allow to measure user activity and develop navigation profiles in order to improve the websites.

Page 32 Student mode 1. It adjusts the swash-plate to operate correctly for each control near the hovering point using the corresponding compensation mixings. Camber Mix Camber Mix [Corresponding model type]: The screen depends on the model type. All of this is to improve our services.

Connector for trainer function TRAINER When you use trainer function, connect the optional trainer cable between the transmitters ,anual teacher and student. Page of Go. Do not discharge Li-Ion batteries at currents which exceed the discharge current rating of the battery.


This stylus pen can let you do more precise operation than fingers without damaging the surface. Reverses the direction of operation of the sticks, switches, trim levers, knobs, etc.

Install the Futaba FX40 test program. Manuzl needle curve can be set. Throttle mixing This function corrects slowing of engine When correction is necessary, touch the mixing speed caused by swash plate operation at aileron corresponding to the mixing that needs correction or elevator operation.

For types, all settings will be lost. Otherwise set it to “8CH”. Common Operations Used In Function Setup Screen Common operations used in function setup screen This section describes the functions often used at the function setup screen. US only 72 or 50 MHz bands Modulation: Do not leave a Li-Ion battery unattended at any time while being charged or discharged.

We recommend you to turn off the backlight by setting the backlight power-off time to about one minute.

Throttle-stick Calibration Futaba 14MZ and FX40

Preset Model Types Numerous aircraft configurations are already programmed into the 14MZ — seven wing types and three tail types.

Switch the operation mode according to the set function.

Mixing Rate Linkage Compensation This compensation mixing is used to correct the This compensation mixing is used to correct the tendency of the swash-plate for each control near tendency of manuzl swash-plate for pitch control at low the hovering point.

Do not attempt to charge Li-Ion batteries with a charger that is NOT designed for Li-Ion batteries, as permanent damage to the battery and charger could result. Its frequency can be changed within the range of nanual frequency band of the module used. Compact Flash The model data and music files, voice files, picture image files are stored to Compact flash CF card.

Just pull out a switch to remove it, and plug in the style you prefer — tall or short, button or toggle, spring-loaded or positionable. The data of up to 30 models can be saved to the transmitter. Move the slide lever to the right end, and then install the battery in the holder.


Turn the CF card so that the name seal faces to the back of the transmitter. When setting a switch. Push the battery to mmanual left with your finger. Manuak key In addition to touch panel, you can select items by rotating the rotary keys to the left or to the right.

Operating instructions FUTABA 14MZ |

If you continue pressing it, the trim position starts to move faster. Curves which are symmetrical to the left and right of center can also be set.

Page Common operations used in function setup screen This section describes the functions often used at the function setup screen. Mznual must have an old software because the program we are going to use is only made for an old version of Futaba FX The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up. You manial contact your local recycling center for information manuual where to return the spent bat lithium-ion Li-Ion batteries.

Although you may notice the flickering of the numbers on the LCD screen, this is not an abnormal, because the LCD screen is frequently refreshing those even if those numbers are unchanged. Select the frequency you want use. Removal 14ma CF card: Do not use any other chargers except CR that is for 12V application to charge the LT2F battery through this connector.

Page PIT to RUD mixing Revolution mixing Use this mixing when you want to suppress the reaction torque generated by main rotor pitch and speed changes at pitch operation.