ASTM B258 PDF

This standard is issued under the fixed designation B ; the number immediately 1 This specification is under the jurisdiction of ASTM Committee B- 1 on. Buy ASTM B R SPECIFICATION FOR STANDARD NOMINAL DIAMETERS AND CROSS-SECTIONAL AREAS OF AWG. ASTM B Standard Specification for Standard Nominal Diameters and Cross-Sectional Areas of AWG Sizes of Solid Round Wires Used.

Author: Kazik Kirisar
Country: Niger
Language: English (Spanish)
Genre: Health and Food
Published (Last): 22 April 2011
Pages: 224
PDF File Size: 11.76 Mb
ePub File Size: 7.5 Mb
ISBN: 669-3-80085-603-8
Downloads: 71911
Price: Free* [*Free Regsitration Required]
Uploader: Kegami

Enter your personal account email address to request a password reset: Register for a trial account. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units.

F Standard Specification for Driven Fasteners: A circular mil is the area of a wire one mil in diameter. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. This specification prescribes the standard nominal diameters and cross-sectional areas of American Wire Gage AWG sizes of solid round wires, used as electrical conductors, and gives equations and rules for the calculation of standard nominal mass and lengths, resistances, and breaking or rated strengths of such wires.

You may delete a document from your Alert Profile at any time. Copyright Compu-tecture, Inc. Are you sure you want to empty the cart?

The sixth power of is very close to 2, [5] which leads to the following rules of thumb:. Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. Mark Lund, PowerStream Inc. As the voice of the U.

  CARLOS LARIOS OCHAITA DERECHO INTERNACIONAL PUBLICO PDF

AWG is also commonly used to specify body piercing jewelry sizes especially smaller sizeseven when the material is not metallic. Each system shall be used independently of the other.

Print 1 2 3 4 5 page sstarting from page current page. This standard is also available to be included in Atm Subscriptions.

American wire gauge

This standard is not included in any packages. The table below shows various data including both the resistance of the various wire gauges and the allowable current ampacity based on plastic insulation. If the document is revised or amended, you will be notified by email.

Archived from the original on 22 July Need more than one copy? The AWG tables are for a single, solid, round conductor. Combining values of the two systems may result in nonconformance with the specification.

Sizes with multiple zeros are successively larger than No. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Each system shall be used independently of the other. AWG gauges are also used to describe stranded wire. Turns of wire is an upper limit for wire with no insulation. The AWG of a stranded wire is determined by the cross-sectional area of the equivalent solid conductor.

  ELECTRONICA DIGITAL ROGER L.TOKHEIM PDF

Link to Active This link will always route to the current Active version of the standard. This standard is not included in any packages. For conductor sizes designated by AWG or kcmil sizes, the requirements in SI units have been numerically converted from the corresponding values stated or derived, aastm inch-pound units.

Add to Alert PDF. This abstract is a brief summary of the referenced standard. A of approximately 1. Subscription pricing is determined by: For conductor sizes designated by AWG or kcmil sizes, the requirements in Ast units have been numerically converted from the corresponding values stated or derived, in inch-pound units.

American Wire Gauge

Royal SocietyII Historical Version s – view previous versions of standard. Stranded wires are specified with three numbers, the overall AWG size, the number of strands, and the AWG size of a strand.

Please first verify your email before subscribing to alerts. An older abbreviation for one thousand circular mils is MCM. Each system shall be used independently of the other. Standards Subscriptions from ANSI provides a money-saving, multi-user solution adtm accessing standards.

Please first verify your email before subscribing to alerts.