This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D02 on. ASTM D Standard Test Method for Gage Vapor Pressure of Liquefied Petroleum (LP) Gases (LP-Gas Method). VAPOR PRESSURE ASTM D TECHNICAL SPECIFICATIONS. VAPOR PRESSURE CYLINDER UPPER CHAMBER. Stainless steel upper chamber with .

Author: Kidal Durisar
Country: Mozambique
Language: English (Spanish)
Genre: Sex
Published (Last): 18 October 2016
Pages: 129
PDF File Size: 10.91 Mb
ePub File Size: 5.40 Mb
ISBN: 914-9-84774-392-6
Downloads: 40404
Price: Free* [*Free Regsitration Required]
Uploader: Torisar

ASTM D1267

The ASTM D standard method follows a similar procedure than the Da method, except that the ratio of the volume of the vapor chamber to the volume of the liquid chamber is 2. The entire system is immersed in a water bath at F and once equilibrium is attained the observed pressure from wstm measuring device is reported as the Reid Vapor Pressure.

Like in the Da method, there is confusion about the units used for this property. For determination of the vapor pressure of gasoline-oxygenate blends, refer to Test Method D Units Like in the Da method, there is confusion about sstm units used for this property. The ASTM D method [1] covers the experimental procedure to obtain the vapor pressure of crude oils. Campbell [5] reports that the air was removed from the cell where the RVP was measured.

The calculation of the oil pseudo-components physical properties is very important since they define the computation of fugacities and equilibrium ratios that are part of the flash calculations used in vapor pressure determination.

True Vapor Pressure F This property is similar to the Vapor Pressure calculation except that the flash calculation is performed at a specific temperature of F.

Vapor Pressure, also known as bubble point pressure and true vapor pressure, is the pressure where the first bubble of vapor is formed at a given temperature.

Reid Vapor Pressure Bath – Koehler Instrument Company, Inc.

Previous calculations in VMGSim did not take into account the air saturation, which caused the results to be lower. The following link provides additional information astj the instruction manual or original manufacturer’s brochure. Calculations were done using the Advanced Peng-Robinson property package.

  FLUKE 9143 PDF

These properties are new to VMGSim and are labeled as: This property is similar to the Vapor Pressure calculation except that the flash calculation is performed at a specific temperature of F.

This option is activated through a check box that can be found in the Special Properties Unit Operation or the Refinery and Natural Gas tabs from the Material Stream as seen in the following figures. Email Asttm or call toll-free: Hoke Petroleum Gas Sampling Cylinder.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Validation examples are also included. Gas Conditioning and Processing 7 th Ed. Because of this the D method will be used to calculate this value.

Product Description The K Reid Vapor Pressure Cylinders are polished stainless steel test cylinders for vapor pressure tests of liquid petroleum products, volatile crude oil and liquefied petroleum gas LPG.

Koehler K11500 (1-opening type) Reid Vapor Pressure Cylinder

VMGSim calculates the vapor pressure by flashing the mixture of interest using a vapor fraction equal to zero at the temperature specified in the stream that d11267 the mixture. Once this was done, a close match between calculated and experimental values of the distillation curve was obtained.

The Reid Vapor Pressure is an important property of gasolines and jet fuels and it is used as a criterion for blending of products.

Consists of upper chamber and lower chamber in required 4: The ratio of the volume of the vapor chamber to the volume of the liquid chamber is 4. The Reid vapor pressure differs from the true vapor pressure of the sample due to some small sample vaporization and the presence of water vapor and air in the confined space.

The air saturation can be activated through the same check box as in the Reid Vapor Pressure calculation. Petroleum Gas Sampling Cylinder.

Right-click to open the PDF in a new window or download it: For determination of the vapor pressure of liquefied petroleum gases, refer to Test Method D or Test Method D Encyclopedia of Chemical Processing and Design: Historical Version s – view previous versions of standard.

This is no longer the case since VMGSim 9.


Vapor Pressure of Petroleum Products Introduction Many problems involving hydrocarbon systems include a specification of some sort of vapor pressure measurement. Since most vapor pressures are reported ast, absolute pressures, most observers expect the Reid Vapor Pressure to follow this norm.

Request prices on the required pressure gauges, thermometer, sample transfer connection and manometer. The precision for crude oil has not been determined since the early s see Note 3.

ASTM D – Parkes Scientific Canada

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Lab Equipment for Sale: Although the units have changed, the calculated values are the same as in previous versions since the internal flash calculations are still the same and based on absolute pressures.

Type text as it appears:: Summary of Vapor Pressure Definitions The following tables show the principal characteristics of the previously described vapor pressure definitions. General Use laboratory apparatus balances, baths, blenders, centrifuges, chart recorders, freezers, fume hoods, furnaces, glassware washers, glove boxes, mixers, moisture testing, ovens, pumps, shakers, vacuum equipment, water purification This test method covers the Reid Vapor Pressure determination of gasoline, volatile crude oils, and other volatile petroleum products.

Petroleum Products and Biofuel lab apparatus baths, calorimeters, color measurement, density meters, flash point, hydrogenators, oil testing, penetrometers, surface wstm, vapor pressure, viscometers and rheometers, Conforms to the specifications of: The storage temperature is defined by the specified temperature in the stream that contains the mixture of interest.

Examples of these definitions are: The method is dd1267 similar to Da but in this case the air saturation is not required. This example has been done using the Advanced Peng-Robinson property package. IP is a test method for determination of the air-saturated vapor pressure of crude oil.

O-ring gaskets provide tight seal between chambers and at gauge coupling. Pharmaceutical laboratory apparatus stability chambers, tablet disintegration, tablet dissolution, tablet hardness, V-blenders,